![]() ![]() Do not go to disinfect if can't achieve disinfection condition because improper disinfection may reduce the hatching rate. The fertilized egg is covered with a layer of powdery substance, which is strictly prohibited to put into fridge and wash.Ģ- The surface of egg shell is required to be no deformity, cracks or any spots.ģ- There's no need to be very careful on disinfecting fertilized eggs. The best temperature for saving fertilized eggs is 10-15 ☌. Then how to choose?ġ-ğertilized Eggs must be fresh and generally within 4-7 days after laying is the best. The first step for hatching is choosing best fertilized eggs. Press button "+" or "-" until "CA" is illustrated on the temperature display.ĥ. If it illustrates a wrong value, you should put a calibrated thermometer into the incubator and watch for the temperature differentials between calibrated thermometer and controller.ġ.Ĝalibrate the the transmitter dimension.(CA)ģ. Calibrating the Temperature Transmitter(CA) The thermometer is set at O ☌(32 ℉) before shipment. Re-set the temperature or add water will solve this problem.Ĭ. The product will make alarm calls at low temperature or humidity. Press button "+" or to set required humidity value. Press button "+" or "-" until "AS" is illustrated on the temperature display.Ĥ. User can adjust humidity according to the egg category and local climate.Ģ. Setting Humidity(AS) The humidity is set at 60% before shipment. Setting Upper & Lower Temperature Limits For example, if the upper limit is set at 38.2 ☌(100.8 ℉) while lower limit is set at 37.4 ☌ (99.3 ℉), the incubator temperature can only be adjusted within this range.ī. Press button "+" or "-" until "AH" is illustrated on the temperature display.Ī2. Press button "+" or "-" to set required temperature alarm value.įor high temperature alarm(AH): 1. Press button to set required temperature alarm value.įor low temperature alarm(AL): The humidi to make any changes to these settings.Ĥ. Press button until "AL" is illustrated on the temperature display.Ĥ. The alarm value for high and low temperature is set at 1 ☌ (33.8 ☏) before shipment.įor low temperature alarm(AL): 1. If the incubator cant reach to 380 C(1000 F) after working for several hours, please check:(l) the setting temperature is above 380 ☌(1000 ℉) (2) the fan is not broken (3) the cover is closed (4) the room temperature is above 180C(64.40 F).Ģ- Press button "+" or "-" to set required temperature.ģ- Press button "Set" to exit setting process.Ĥ- Press the SET button and plug in at the same time to restore factory settings al. ![]() User can adjust temperature according to the egg category and local climate. Setting Temperature The incubator temperature is set at 38 ☌ (100 ☏) before shipment. The factory default settings will be restored after simultaneously pressing RESET and ON/OFF switch.Ī. Hatching time will be reset after long pressing RESET button. The incubator will turn eggs after pressing RESET button. Do not put on the cover for observation.ġ-8- Press reset button to check the automatic egg turning function.lt turns every two hours,lasting 10 seconds. The eggs are gently rolled right and left by 45 degrees for 10 seconds and then at random directions. Please pay close attention to egg turning at first use. The interval for egg turning is set at 2 hours. Unpack the incubator and fill the water channel will help to increase humidity gradually.(Warm water is preferred.)ħ. Temperature and humidity of this unit won't reach to the setting value when you newly plug in the power cord, and this unit will send out alarms of low temperature and low humidity.ĥ.Ĝancel the alarm by pressing any green button.Ħ. No need to turn on the switch on the panel of the unit.Ĥ. 1.Ĝheck that the incubator motor is connected to the controller.ģ. DO NOT PUT ANY EGGS INTO INCUBATOR WHEN TESTING. ![]() IT'S RECOMMENDED TO PERFORM MACHINE TEST BEFORE HATCHING EGGS IN CASE INCUBATED EGGS GO BAD.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |